Sale Leads

Tobee® SP/SPR vertical slurry pumps Tobee® TP100RV Vertical Spindle Pump is mainly used in a variety of sump conditions, It can also be readily applied on floating dewatering or other floating pump platforms. As a true cantilevered vertical slurry pump, TP100RV vertical spindle pump does not have submerged bearings or seals, thus, eliminating the primary failure mechanism for similarly fielded pump lines. Design Features 1. Bearing Assembly - The bearings, shaft and housing are generously proportioned to avoid problems associated with the operation of cantilevered shafts in the first critical speed zones. The assembly is grease lubricated and sealed by labyrinths; the upper is grease purged and the lower protected by a special flinger. The upper or drive end bearing is a parallel roller type whilst the lower bearing is a double taper roller with preset end float. This high performance bearing arrangement and robust shaft eliminates the need for a lower submerged bearing. 2. Column Assembly - Completely fabricated from mild steel. The TPR model is elastomer covered. 3. Casing - Has a simple bolt-on attachment to the base of the column. It is manufactured from a wear resistant alloy for the SP and from moulded elastomer for the TPR. 4. Impeller - Double suction impellers (top and bottom entry) induce low axial bearing loads and have heavy deep vanes for maximum wear resistance and for handling large solids. Wear resistant alloys, polyurethane and moulded elastomer impellers are interchangeable. The impeller is adjusted axially within the casting during assembly by external shims under the bearing housing feet. No further adjustment is necessary. 5. Upper Strainer - Drop-in metal mesh, snap-on elastomer or polyurethane for TP and TPR pumps. Strainers fit in column openings. 6. Lower Strainer - Bolted metal or polyurethane for TP, moulded snap-on elastomer for TPR. 7. Discharge Pipe - Metal for TP, elastomer covered for TPR. All wetted metal parts are completely rust protected. 8. Submerged Bearings - None 9. Agitation - An external agitator spray connection arrangement can be fitted to the pump as an option. Alternatively, a mechanical agitator is fitted to an extended shaft protruding from the impeller eye. 10. Materials - Pumps can be manufactured in abrasive and corrosive resistant materials. Tobee® Vertical Spindle Pumps are available in a wide range of popular sizes to suit most pumping applications: • Minerals processing • Coal preparation • Chemical processing • Effluent handling • Abrasive and/or corrosive slurries • Large particle sizes • High density slurries • Sand and gravel and almost every other tank, pit or hole-in-theground slurry handling situation.

150SV-SP Vertical Slurry Pump is available in a wide range of popular sizes to suit most pumping applications. Thousands of these pumps are proving their reliability and efficiency worldwide in Minerals processing, Coal preparation, Chemical processing, Effluent handling, Sand and gravel and almost every other tank, pit or hole-in-the ground slurry handling situation. 1.Vertical,Submerged,Cantilevered shaft sump slurry pump 2.Bearing Assembly - The bearings, shaft and housing are generously proportioned to avoid problems associated with the operation of cantilevered shafts in the first critical speed zones. 3..Column Assembly - Completely fabricated from antiwear carbon steel. The TPR model is rubber covered. 4.Shaft - Different length of the pump drive shaft or suction extension pipe could be selected 5.Casing - TP(R) has a simple bolt-on attachment to the base of the column. It is manufactured from a wear resistant alloy for the TP pump series and from moulded Rubber for the TPR pump series. 6.Impeller - Double suction semi-open impeller design, Wear resistant alloys, polyurethane and moulded elastomer impellers are interchangeable. 7.Upper Strainer - Drop-in metal mesh; snap-on elastomer or polyurethane for TP and TPR pumps. Strainers fit in column openings. 8.Lower Strainer - Bolted metal or polyurethane for TP pumps; moulded snap-on elastomer for TPR pumps. 9.Discharge Pipe - Metal for TP pumps; Rubber covered for TPR pumps. All wetted metal parts are completely rust protected 10..Agitator option keeps solids in suspension,Alternatively, a mechanical agitator is fitted to an extended shaft protruding from the impeller eye. 11.Don’t need any seal and seal water.

Tobee® TP/TPR Vertical Slurry Pumps are interchangeable with Warman SP/SPR vertical slurry pumps, As a kind of heavy duty cantilever sump pump, it is designed for applications requiring greater reliability and durability than conventional vertical process pumps. Fully elastomer lined or hard metal fitted. No submerged bearings or packing. High capacity double suction design. Optional recessed impeller and suction agitator available. Vertical Slurry Pumps Specification: Size (discharge): 40mm to 300mm Capacity: 7.2~ 1492 m3/hr Head: 5.5m ~ 47 m Handing solids: 0 ~ 65mm Concentration: 0%~ 70% Material:High chrome alloy,Rubber,Stainless steel etc. Detailed specification: 1.Cantilevered shaft design. 2.Double suction semi-open impeller. 3.Agitator option keeps solids in suspension. 4.TPR models feature full rubber covering for corrosion resistance. 5.Recessed impeller option passes oversized material. 6.Fully elastomer lined or hard metal fitted. No submerged bearings or packing. High capacity double suction design. Optional recessed impeller and suction agitator available. 7.No submerged bearings or packing. High capacity double suction design. Optional recessed impeller and suction agitator available. Tobee® SP/SPR Vertical Slurry Pumps Applications: The SP/SPR vertical slurry pumps are available in a wide range of popular sizes to suit most pumping applications. The SP/SPR sump pumps are proving their reliability and efficiency worldwide in: minerals processing, coal preparation, chemical processing, effluent handling, sand and gravel and almost every other tank, pit or hole-in-the ground slurry handling situation. The SP/SPR pump design with either hard metal (SP) or elastomer covered (SPR) components makes it ideal for abrasive and/or corrosive slurries, large particle sizes, high density slurries, continuous or “snore” operation, heavy duties demanding cantilever shafts.

Tobee® SP/SPR vertical slurry pump is designed for applications requiring greater reliability and durability than conventional vertical process pumps can offer. Fully elastomer lined or hard metal fitted. No submerged bearings or packing. High capacity double suction design. Customized submerged length and suction agitator available. The SP/SPR vertical sump pump ideally suited for heavy continuous handling of abrasive and corrosive liquids and slurries whilst submerged in sumps or pits. Design Features: √ Less wear, less corrosion Wetted components are available in a wide range of alloys and elastomers, from which Weir Minerals selects the optimum combination of materials for maximum resistance to wear in virtually any industrial application, including those demanding both abrasion and corrosion resistance and where larger particles or high density slurries are encountered. • Abrasion resistant A05 Ultrachrome® alloy. • Abrasion/corrosion-resistant A49 Hyperchrome® alloy. • Corrosion-resistant stainless steels. • Natural and synthetic elastomers. √ No submerged bearing failures The robust cantilever shaft avoids the need for lower submerged bearings - which are often the source of premature bearing failure. • Heavy duty roller bearings, above mountingplate. • No submerged bearings. • Labyrinth/flinger bearing protection. • Rigid, large diameter shaft. √ No shaft sealing problems The vertical cantilever design requires no shaft seal. √ No priming required The top and bottom inlet design is ideally suited for “snore” conditions. √ Less risk of blocking The screened inlets and large impeller passages reduce the risk of blockages. √ Zero ancillary water costs The vertical cantilever design with no gland or submerged bearings avoids the need for expensive gland or bearing flushing water. Tobee® SP/SPR Vertical Slurry Pumps Applications: The SP/SPR vertical slurry pumps are available in a wide range of popular sizes to suit most pumping applications. The SP/SPR sump pumps are proving their reliability and efficiency worldwide in: minerals processing, coal preparation, chemical processing, effluent handling, sand and gravel and almost every other tank, pit or hole-in-the ground slurry handling situation. The SP/SPR pump design with either hard metal (SP) or elastomer covered (SPR) components makes it ideal for abrasive and/or corrosive slurries, large particle sizes, high density slurries, continuous or “snore” operation, heavy duties demanding cantilever shafts.

Tobee® TP/TPR Vertical Slurry Pumps are interchangeable with Warman SP/SPR vertical slurry pumps, As a kind of heavy duty cantilever sump pump, it is designed for applications requiring greater reliability and durability than conventional vertical process pumps. Fully elastomer lined or hard metal fitted. No submerged bearings or packing. High capacity double suction design. Optional recessed impeller and suction agitator available. Vertical Slurry Pumps Specification: Size (discharge): 40mm to 300mm Capacity: 7.2~ 1492 m3/hr Head: 5.5m ~ 47 m Handing solids: 0 ~ 65mm Concentration: 0%~ 70% Material:High chrome alloy,Rubber,Stainless steel etc. Detailed specification: 1.Cantilevered shaft design. 2.Double suction semi-open impeller. 3.Agitator option keeps solids in suspension. 4.TPR models feature full rubber covering for corrosion resistance. 5.Recessed impeller option passes oversized material. 6.Fully elastomer lined or hard metal fitted. No submerged bearings or packing. High capacity double suction design. Optional recessed impeller and suction agitator available. 7.No submerged bearings or packing. High capacity double suction design. Optional recessed impeller and suction agitator available. Tobee® SP/SPR Vertical Slurry Pumps Applications: The SP/SPR vertical slurry pumps are available in a wide range of popular sizes to suit most pumping applications. The SP/SPR sump pumps are proving their reliability and efficiency worldwide in: minerals processing, coal preparation, chemical processing, effluent handling, sand and gravel and almost every other tank, pit or hole-in-the ground slurry handling situation. The SP/SPR pump design with either hard metal (SP) or elastomer covered (SPR) components makes it ideal for abrasive and/or corrosive slurries, large particle sizes, high density slurries, continuous or “snore” operation, heavy duties demanding cantilever shafts.

Tobee™ 65QV-SP(R), 100RV-SP(R), 150SV-SP(R) Vertical Slurry Pumps are centrifugal slurry pumps submerged in sump to work.They are designed for delivering abrasive,large particle and high density slurries.These pumps have no need of any shaft seal and sealing water. They can also be operated normally for insufficient suction duties.Wet parts of type SP pump are made of abrasion-resistant metal. All parts of type SPR pump immersed in liquid are lined with rubber outer liner.They are suited to transport non-edge angle abrasive slurry. Specification: Size (discharge): 40mm to 300mm Capacity: 7.2~ 1492 m3/hr Head: 5.5m ~ 47 m Handing solids: 0 ~ 65mm Concentration: 0%~ 70% Material:High chrome alloy,Rubber,Stainless steel etc.

65QV SP Vertical Slurry Pumps Applications: The SP/SPR verical slurry pumps are available in a wide range of popular sizes to suit most pumping applications. The SP/SPR sump pumps are proving their reliability and efficiency worldwide in: minerals processing, coal preparation, chemical processing, effluent handling, sand and gravel and almost every other tank, pit or hole-in-the ground slurry handling situation. The SP/SPR pump design with either hard metal (SP) or elastomer covered (SPR) components makes it ideal for abrasive and/or corrosive slurries, large particle sizes, high density slurries, continuous or “snore” operation, heavy duties demanding cantilever shafts. Tobee® SP/SPR Vertical Slurry Pumps Applications: The SP/SPR vertical slurry pumps are available in a wide range of popular sizes to suit most pumping applications. The SP/SPR sump pumps are proving their reliability and efficiency worldwide in: minerals processing, coal preparation, chemical processing, effluent handling, sand and gravel and almost every other tank, pit or hole-in-the ground slurry handling situation. The SP/SPR pump design with either hard metal (SP) or elastomer covered (SPR) components makes it ideal for abrasive and/or corrosive slurries, large particle sizes, high density slurries, continuous or “snore” operation, heavy duties demanding cantilever shafts. HEBEI TOBEE PUMP CO.,LIMITED Add: Hi-tech Development Zone | Shijiazhuang City | Hebei Province | China. Sales Engineer / International Dept. Bella Zhang Email:sales3(at)tobeepump.com Mob:+86-18000656103 Webchat/WhatsApp:+86-18000656103 Fax:+86-0311-87221317 Web: www.tobee.cc Web: www.tobee.store Web: www.hydroman.cn Web: www.tobeepump.com Web: www.slurrypumpsupply.com

Tobee® TG12x10G Dredging Sand Pump is a single stage, single casing, centrifugal horizontal pump driven by electric motor diesel engine. Large flow passage allows large particle solids, with advantages of high efficiency, wear resistant, wide flow channel, good ability of NPSH, stable performance, easy assembly, The discharge outlet can be adjusted at any direction, It is world’s standard for dredge, gravel or large particle slurries applications. Design Features: • Advanced hydraulic model, CAD 3D design, high efficiency and obvious energy-saving • Large dredging sand depth, high density of dredging mud, good pump NPSH and strong suction lift ability. • Strong through-put, The dredging pump can persistently discharge gravel, high plastic soil lump,etc. • Wide application, The sand pump can be used in various kinds of soil quality. • The TG sand pump can be directly matched with electric motor or diesel engine. • The TG sand pump impeller is 3 or 5 vanes for large particles delivering. • Little hydraulic loss, high efficiency and low oil-consumption. • Steady operating, little vibration, low noise. • Simple & reliable constrution, easily disassembly & assembly,convenient maintainc • Reliable sealing without leakage. • Long operating life of wear parts. HEBEI TOBEE PUMP CO.,LIMITED Add: Hi-tech Development Zone | Shijiazhuang City | Hebei Province | China. Email: Inquiry(a)tobeepump.com Mob: +86-15630104263 Skype: Tobee.Pump Fax: +86 311-87221317 Web: www.tobeepump.com Web: www.slurrypumpsupply.com Web: www.tobee.cc Web: www.hydroman.cn Web: www.tobee.store

Tobee® TG12x10G Dredging Sand Pump is a single stage, single casing, centrifugal horizontal pump driven by electric motor diesel engine. Large flow passage allows large particle solids, with advantages of high efficiency, wear resistant, wide flow channel, good ability of NPSH, stable performance, easy assembly, The discharge outlet can be adjusted at any direction, It is world’s standard for dredge, gravel or large particle slurries applications. Design Features: • Advanced hydraulic model, CAD 3D design, high efficiency and obvious energy-saving • Large dredging sand depth, high density of dredging mud, good pump NPSH and strong suction lift ability. • Strong through-put, The dredging pump can persistently discharge gravel, high plastic soil lump,etc. • Wide application, The sand pump can be used in various kinds of soil quality. • The TG sand pump can be directly matched with electric motor or diesel engine. • The TG sand pump impeller is 3 or 5 vanes for large particles delivering. • Little hydraulic loss, high efficiency and low oil-consumption. • Steady operating, little vibration, low noise. • Simple & reliable constrution, easily disassembly & assembly,convenient maintainc • Reliable sealing without leakage. • Long operating life of wear parts. Tobee® TG12x10G Dredging Sand Pump Shaft Seal Arrangement: • Packing Seal is a general shaft seal.It applys to various pumping conditions, PTFE and Graphite materials of Packing can be used in high corrosive slurries or high temperature conditions.Using ceramic shaft sleeve,For high abrasion conditions, The ceramic shaft sleeve is available. • Expeller Seal is an impeller force of reversed centrifugal force, preventing slurry leakage. Expeller seal can be used on the single-stage pump when the positive pressure of pump inlet is no more than 10% of pump outlet pressure or on the first-stage pump in the pump series. • Mechanical Seal is advanced sealing technique without sealing leakage, integrating construction, convenient installation & replacement, various constructions suit for all kinds of conditions. Tobee® Dredging Sand Pumps are used for rivers, lakes and sea sand dredging, blowing sand reclamation, river dredging, pumping sand selected iron ore, tailings pumping, coal mines, power plants and mining companies such as transport medium containing solid particles. HEBEI TOBEE PUMP CO.,LIMITED Email: Sales3(a)tobeepump.com Mob: +86-18000656103 Skype: Tobee.Pump Fax: +86 311-87221317 Web: www.tobeepump.com Web: www.slurrypumpsupply.com Web: www.tobee.cc Web: www.hydroman.cn

Tobee® 10x8E-M Centrifugal Medium Duty Slurry Pump shipped to India old-customer. And it is rubber lined with expeller seal. 10x8E-M Medium Duty Slurry Pump is cantilevered, horizontal and centrifugal with double casing structure, It mainly suitable for pumping medium concentration slurries, 10x8E-M slurry pump applies in coal washer processing, handling with the fine ore and tailings in metal mine, handing combined bottom and fly ash in a thermal power station etc. HEBEI TOBEE PUMP CO.,LIMITED Add: Hi-tech Development Zone | Shijiazhuang City | Hebei Province | China. Sales Engineer / International Dept. Bella Zhang Emails:sales3(at)tobeepump.com Mob:+86-18000656103 WhatsApp:+86-18000656103 Fax:+86-0311-87221317 Web: www.tobee.cc Web: www.tobee.store Web: www.hydroman.cn Web: www.tobeepump.com Web: www.slurrypumpsupply.com

Tobee manufactures all series of G and GH gravel sand pumps and parts. ( 6/4D-G, 6/4E-G, 8/6E-G, 10/8S-G, 10/8S-GH, 10/8F-G, 12/10F-G, 12/10G-G, 12/10G-GH, 14/12G-G, 14/12T-G, 16/14G-G, 16/14T-G, 16/14TU-GH, 18/16TU-G, 18/16TU-GH ) Tobee® G/GH Gravel pumps are designed to handle large particles for gravel and dredging operations, with a wide flow channel, It is mainly applied for continuous handling of the most difficult higher abrasive gravels, slurries, sands, bentonite, clay, rock etc. HEBEI TOBEE PUMP CO.,LIMITED Sales Engineer / International Dept. Add: Hi-tech Development Zone | Shijiazhuang City | Hebei Province | China. Bella Zhang Emails:sales3(at)tobeepump.com Mob:+86-18000656103 WhatsApp:+86-18000656103 Fax:+86-0311-87221317 Web: www.tobee.cc Web: www.tobee.store Web: www.hydroman.cn Web: www.tobeepump.com Web: www.slurrypumpsupply.com

Tobee® TG12x10G Dredging Sand Pump is a single stage, single casing, centrifugal horizontal pump driven by electric motor diesel engine. Large flow passage allows large particle solids, with advantages of high efficiency, wear resistant, wide flow channel, good ability of NPSH, stable performance, easy assembly, The discharge outlet can be adjusted at any direction, It is world’s standard for dredge, gravel or large particle slurries applications. Tobee® Dredging Sand Pumps are used for rivers, lakes and sea sand dredging, blowing sand reclamation, river dredging, pumping sand selected iron ore, tailings pumping, coal mines, power plants and mining companies such as transport medium containing solid particles. HEBEI TOBEE PUMP CO.,LIMITED Sales Engineer / International Dept. Add: Hi-tech Development Zone | Shijiazhuang City | Hebei Province | China. Bella Zhang Emails:sales3(at)tobeepump.com Mob:+86-18000656103 WhatsApp:+86-18000656103 Fax:+86-0311-87221317 Web: www.tobee.cc Web: www.tobee.store Web: www.hydroman.cn Web: www.tobeepump.com Web: www.slurrypumpsupply.com

Tobee® TG12x10G Dredging Sand Pump is a single stage, single casing, centrifugal horizontal pump driven by electric motor diesel engine. Large flow passage allows large particle solids, with advantages of high efficiency, wear resistant, wide flow channel, good ability of NPSH, stable performance, easy assembly, The discharge outlet can be adjusted at any direction, It is world’s standard for dredge, gravel or large particle slurries applications. Design Features: • Advanced hydraulic model, CAD 3D design, high efficiency and obvious energy-saving • Large dredging sand depth, high density of dredging mud, good pump NPSH and strong suction lift ability. • Strong through-put, The dredging pump can persistently discharge gravel, high plastic soil lump,etc. • Wide application, The sand pump can be used in various kinds of soil quality. • The TG sand pump can be directly matched with electric motor or diesel engine. • The TG sand pump impeller is 3 or 5 vanes for large particles delivering. • Little hydraulic loss, high efficiency and low oil-consumption. • Steady operating, little vibration, low noise. • Simple & reliable constrution, easily disassembly & assembly,convenient maintainc • Reliable sealing without leakage. • Long operating life of wear parts. Tobee® TG12x10G Dredging Sand Pump Shaft Seal Arrangement: • Packing Seal is a general shaft seal.It applys to various pumping conditions, PTFE and Graphite materials of Packing can be used in high corrosive slurries or high temperature conditions.Using ceramic shaft sleeve,For high abrasion conditions, The ceramic shaft sleeve is available. • Expeller Seal is an impeller force of reversed centrifugal force, preventing slurry leakage. Expeller seal can be used on the single-stage pump when the positive pressure of pump inlet is no more than 10% of pump outlet pressure or on the first-stage pump in the pump series. • Mechanical Seal is advanced sealing technique without sealing leakage, integrating construction, convenient installation & replacement, various constructions suit for all kinds of conditions. HEBEI TOBEE PUMP CO.,LIMITED Email: Sales3(a)tobeepump.com Mob: +86-18000656103 Fax: +86 311-87221317 Web: www.tobeepump.com Web: www.slurrypumpsupply.com Web: www.tobee.cc Web: www.hydroman.cn Web: www.tobee.store

10x8 S-G Gravle and Sand Pump has rational structure, high efficiency, reliable operation, convenient maintenance and other advantages. 10x8S-G Gravel Pump is the world's standard for dredge and gravel applications. The range provides excellent wear life while maintaining efficiency during the wear cycle providing the best total operating cost. A wide variety of shaft seals provide a perfect fit for a wide range of applications. Pass very large solids not capable of being pumped by TH series slurry pumps. Design Features: • G gravel pump uses modern CAD design method, and has excellent hydraulic performance, high efficiency, and low wear rate. • G gravel pump has wide runner, good anti-clogging performance, and excellent cavitation performance. • G gravel pump uses expeller and filler combined seal and mechanical seal, ensuring that the slurry doesn't leak. • The reliability design greatly improves mean time between failures (MTBF) of complete machine. • G gravel pump uses thin oil lubrication metric bearing, and rationally sets lubrication and cooling system to ensure that the bearing operates at low temperature. • Flow passage components are made of special materials, so they have good wear resistance and corrosive resistance; after special processing, they are used for seawater dusting, and seawater and salt mist electric chemical corrosion conditions. • In allowable pressure range, it can be used in series in stages, and allowable maximum working pressure is 3.6Mpa. Our Team In order to sustain and grow organizations we must recognize that your satisfaction is pivotal, as you ultimately determine the quality and the value that you perceive from our products. Tobee® Pump outlines a set of core corporate values that all members in the stakeholder value chain must uphold, and is aligned with the aim to exceed your satisfaction. Email: Sales3(a)tobeepump.com Mob: +86-18000656103 Skype: Tobee.Pump Fax: +86 311-87221317 Web: www.tobeepump.com Web: www.slurrypumpsupply.com Web: www.tobee.cc Web: www.hydroman.cn Web: www.tobee.store

1.5x1 B-THR Rubber Lined Slurry Pumps, Impeller Spare Parts B1052RU55 on 1.5x1 TH Tailing pumps. Tobee® can supply TH slurry pump impeller with kinds of relevant material, such as metal slurry pump impeller, rubber slurry pump impeller, polyurethane slurry pump impeller and ceramic slurry pump impeller. open impeller, closed impeller, and semi-closed impeller Tobee® slurry pump impellers are interchangeable with TH/HH/LM slurry pump impellers, Centrifugal slurry pumps need impeller to produce the centrifugal force which transfer the slurries. The centrifugal force is produced by the impeller which rotates to a certain speed, As main rotating component which normally has vanes to impart the centrifugal force to the liquid, Usually, slurry pump impellers have a plain or a Francis type vane. Centrifugal Slurry Pump Impellers are selected with purpose and are dependent upon the slurry application. Some are better for solids handling, others are better for high efficiency. Read on to find out which slurry pump impeller will be best for your slurry pump application. There are Open, Semi Open and Closed impeller. So slurry pump impeller selection to deal with different slurry with solid have different choices. Slurry pump impeller normally made of High chrome alloy, elastomer, polyurethane and some other customed. But High chrome alloy and elastomer are the main material for the slurry pumps. Email: Sales3@tobeepump.com Mob: +86-18000656103 Skype: Tobee.Pump Fax: +86 311-87221317 Web: www.tobeepump.com Web: www.slurrypumpsupply.com Web: www.tobee.cc Web: www.hydroman.cn Web: www.tobee.store

Tobee® Expeller D028HS1A05 is for the 4/3D Hi-seal slurry pump, It is also one of the important parts of the slurry pump, and be combined with the decompression cover to form the dynamic seal of the slurry pump. It is one of the three types of shaft seals of the slurry pump. Below we will briefly introduce the expeller of the slurry pump: The standard material of the expeller of the slurry pump is generally gray iron or ductile iron, and it can also be made of A05 and A05A as the flow-through part material according to customer requirements. In recent years, most customers prefer AO5 high-chromium wear-resistant alloy material when purchasing. The expeller can not only play a role in sealing, but also play a role in reducing the axial force. If the slurry pump expeller is installed, the direction of the pressure differential force acting on the expeller by the liquid is opposite to the pressure differential force acting on the slurry pump impeller, so that part of the axial force can be offset and the bearing life will be prolonged. Slurry Pump Design Features • Single face, Multiple spring. • Spring protection Of rotation Cartridge. • The wash Spring does not require contact with the medium, thus overcoming the high viscosity. • crystallization of the material blocking the flexibility to protect the compensation ring, extending seal life. • Mechanical seal flush with auxiliary structure, thereby improving the sealing conditions to extend the seal life . • Easy to install without removing the seal cavity install both mechanical seals. • Suitable conditions containing the solid particles. Email: Sales3@tobeepump.com Mob: +86-18000656103 Skype: Tobee.Pump Fax: +86 311-87221317 Web: www.tobeepump.com Web: www.slurrypumpsupply.com Web: www.tobee.cc Web: www.hydroman.cn Web: www.tobee.store

D024E65 Slurry Pump End Cover can be used for 4/3D TH slurry pump, and also can installed for 6x4D-TH slurry pumps. Slurry pump end cover is one of drive pump end parts which is installed on both ends of slurry pump bearing housing to fix the bearings, so end cover of Slurry Pump is an important part for the slurry pump bearing assembly to directly affects the using status of the pump bearing assembly, thereby will directly affect slurry pump operation and work life. Slurry Pump Design Features • Single face, Multiple spring. • Spring protection Of rotation Cartridge. • The wash Spring does not require contact with the medium, thus overcoming the high viscosity. • crystallization of the material blocking the flexibility to protect the compensation ring, extending seal life. • Mechanical seal flush with auxiliary structure, thereby improving the sealing conditions to extend the seal life . • Easy to install without removing the seal cavity install both mechanical seals. • Suitable conditions containing the solid particles. Email: Sales3@tobeepump.com Mob: +86-18000656103 Skype: Tobee.Pump Fax: +86 311-87221317 Web: www.tobeepump.com Web: www.slurrypumpsupply.com Web: www.tobee.cc Web: www.hydroman.cn Web: www.tobee.store

Tobee® SH075C21 Shaft Sleeve is one of the essential shaft seal parts for the 10/8ST-TH, 12/10ST-TH, and 14x12ST-TH Slurry Pumps. The Shaft Sleeve spare part code is 075 and 076. We have a slurry pump shaft sleeve in material 4Cr13, Ceramic coated, tungsten carbide coated and stainless steel, to meet different applications. The slurry pump shaft sleeve protects the pump shaft from slurry abrasion and corrosion, enhancing the pump lifetime. The slurry Pump Shaft Sleeve is also a quick-wear part of slurry pumps. The design and material of the shaft sleeve are significant to slurry pump service life, The slurry pump shaft sleeve protects the pump shaft from abrasion and corrosion within seal arrangements, Tobee offers different materials of shaft sleeve for international brand slurry pumps. A shaft sleeve acts as a shield for the shaft assembly in pumps and compressors. A shaft sleeve is a hollow metal tube, cylindrical in shape, which is mounted over a shaft and shaft assembly to protect it in a corrosive environment. Shaft sleeves are commonly found in single-stage pumps. The pump shaft usually offers protection from corrosion and erosion. The basic function of a shaft sleeve is to protect the shaft from packing wear at the stuffing box. Shaft Sleeves help protect the running surface of the shaft seal or the surfaces in contact from damage or abrasive wear. The hardness of the material used to construct the shaft must be sufficient; Otherwise, it may cause a shaft sleeve to fail. The thermal expansion coefficient must be considered when designing a shaft sleeve. In ideal conditions, the shaft's coefficient of thermal expansion should be equal to that of the shaft sleeve. Tobee® 12/10 ST TH Slurry Pumps Applications: The 12/10 ST TH Slurry Pumps are widely used to transport corrosive/ abrasive and high concentration slurry in many industries. Such as Gold, Silver, Iron ore, Tin, Steel, Coal, Titanium, Copper, Mineral sands, Lead and Zinc. Various other industries include Molybdenum, Electric Utilities, Oil Shale, Water & Sewage Utilities, Building areas, Sand & Gravel, Tobacco and Agriculture (hog, poultry, dairy manure), Mining & Minerals, Grinding and screening, Hydrocyclone separation, Magnetic separation, Flotation, Thickening, Filtration, Leaching, solvent extraction and electrowinning, Pelletizing, Tailings, Metallurgy, Roasting, Annealing and pickling, Coke quenching, Hot strip milling, Neutralisation, Mud handling and waste treatment. Email: Sales3@tobeepump.com Mob: +86-18000656103 Skype: Tobee.Pump Fax: +86 311-87221317 Web: www.tobeepump.com Web: www.slurrypumpsupply.com Web: www.tobee.cc Web: www.hydroman.cn Web: www.tobee.store

Tobee® Slurry Pump Bearing Housing E004M is one of the most important parts in 6x4E-TH Centrifugal Slurry Pumps. The basic number is 004, and it is container of bearings and shaft. There are four clamp bolts through the base which fasten the slurry pump bearing housing. Tobee Slurry Pump Bearing Housings are normally made in grey iron material, ductile iron is also available. The Part Codes: B004M, C004M, D004M, E004M, F004M, X004M, R004M, S004M, T004M, G004M, etc. Bearing Housing with Shaft for Bearing Assembly of Heavy Duty Slurry Pumps. Introduction: Bearing assembly is an assembled part which comprises parts like shaft, bearing housing, bearings, end cover, labyrinth, etc. and is the rotor part of a slurry pump.Heavy duty roller bearings are housed in a re-moveable bearing cartridge. Cartridge type with grease lubricated roller bearings designed for more than 60000 operating hours. Slurry Pump Design Features • Single face, Multiple spring. • Spring protection Of rotation Cartridge. • The wash Spring does not require contact with the medium, thus overcoming the high viscosity. • crystallization of the material blocking the flexibility to protect the compensation ring, extending seal life. • Mechanical seal flush with auxiliary structure, thereby improving the sealing conditions to extend the seal life . • Easy to install without removing the seal cavity install both mechanical seals. • Suitable conditions containing the solid particles. Email: Sales3@tobeepump.com Mob: +86-18000656103 Skype: Tobee.Pump Fax: +86 311-87221317 Web: www.tobeepump.com Web: www.slurrypumpsupply.com Web: www.tobee.cc Web: www.hydroman.cn Web: www.tobee.store

Tobee® Expeller D028HS1A05 is for the 4/3D Hi-seal slurry pump, It is also one of the important parts of the slurry pump, and be combined with the decompression cover to form the dynamic seal of the slurry pump. It is one of the three types of shaft seals of the slurry pump. Below we will briefly introduce the expeller of the slurry pump: The standard material of the expeller of the slurry pump is generally gray iron or ductile iron, and it can also be made of A05 and A05A as the flow-through part material according to customer requirements. In recent years, most customers prefer AO5 high-chromium wear-resistant alloy material when purchasing. The expeller can not only play a role in sealing, but also play a role in reducing the axial force. If the slurry pump expeller is installed, the direction of the pressure differential force acting on the expeller by the liquid is opposite to the pressure differential force acting on the slurry pump impeller, so that part of the axial force can be offset and the bearing life will be prolonged. Slurry Pump Design Features • Single face, Multiple spring. • Spring protection Of rotation Cartridge. • The wash Spring does not require contact with the medium, thus overcoming the high viscosity. • crystallization of the material blocking the flexibility to protect the compensation ring, extending seal life. • Mechanical seal flush with auxiliary structure, thereby improving the sealing conditions to extend the seal life . • Easy to install without removing the seal cavity install both mechanical seals. • Suitable conditions containing the solid particles. Email: Sales3@tobeepump.com Mob: +86-18000656103 Skype: Tobee.Pump Fax: +86 311-87221317 Web: www.tobeepump.com Web: www.slurrypumpsupply.com Web: www.tobee.cc Web: www.hydroman.cn Web: www.tobee.store